General Information

Important Safety Notes:

• Check the inside of the larger pieces in your box for other materials packed inside
• When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching
• We recommend an area approximately 5'x 8' for unobstructed assembling
• You should not need to use excessive force when assembling components

Returns:
If you wish to return your product, please contact us first — we can often help resolve the issue right away.
If a return is still necessary, it must be initiated with the retailer where the product was purchased.

Need Help or Replacement Parts?

Although great care has been taken to ensure proper packaging and handling of this product, occasional issues can occur.

If you need replacement parts, assembly assistance, or have questions about the product, our customer service team is ready to help:

• Website: https://parts.nychbrands.com
• Email: support@zippity-outdoor.com
• Phone: 704-892-5222 or 877-234-6196

Customer service agents are available 9am–5pm EST, Monday–Friday.

For Quick Assistance:

• Have reference item number ZP19069
• Provide the specific part name
• Include the batch lot number found on the end of the box

Detailed Dimensions & Specifications

Product Specifications:

• Overall Width: 65.51 in (60.25 in between posts)
• Overall Height: 38.64 in
• Distance between Pickets: 3.75 in
• Distance off Ground: 2.13 in

A — Post Cap (1)

B — Post Hinge Piece (4)

C — Rail Hinge Piece (4)

D — Top Rail (1)

⅞" x 3" x 60"

E — Bottom Rail (1)

⅞" x 3" x 60"

F — Post (1)

3" x 3" x 37⅝"

G — Picket (12)

⅝" x 1" x 32"

H — Portable Foot (1)

3" W x 16" L

I — Post Insert (1)

J — ¾" Self-Drilling Stainless Steel Screw (16)

K — 2½" Self-Drilling Stainless Steel Screw (4)

L — Spacer (1)

⅝" x ⅞" x 3"

M. ½" Self-Drilling Stainless Steel Screw (2)

N. Panel Lock (2)

O. Silicone No-Scratch Pad (2)

• Insert (12) Pickets (G) into the Bottom Rail (E) until they bottom out inside the rail

• Insert the Top Rail (D) over the pickets

• Drive (8) ¾" Self-Drilling Stainless Steel Screws (J) through the pre-drilled holes in the rails

Note: The top of the pickets should be roughly 3½" above the top of the top rail

• Insert (4) total Rail Hinge Pieces (C) over the ends of the horizontal rails

• Drive (2) ¾" self-drilling stainless steel screws into the pre-drilled holes in each rail hinge piece

• Insert (1) Post Hinge Piece (B) into the groove in the Post (F)
• Use the Spacer (L) to set the height of the hinge piece from the bottom of the post
• Ensure that the hinge peg is facing upward, and drive (1) 2½" Self-Drilling Stainless Steel Screw (K) into the edge of the post to secure the post hinge

Note: The spacer can be removed after screw is put in

• Insert the bottom rail hinge piece of the fence panel into the post hinge piece, and lay the joined post and fence panel on a flat surface

• Slide the remaining post hinge piece up the post channel to align with the top rail
• Drive (1) 2½" Self-Drilling Stainless Steel Screw (K) into the edge of the post to secure the post hinge

• Repeat steps 3.1 through 3.3 using the post from an additional panel, or the Hinged Portable Finishing Post (Item SKU: ZP19063) to end the run
• Use the spacer to achieve consistent hinge height

Note: Please observe the best configuration for a 90° angle below

• Push the Post Insert (I) into the center cavity at the bottom of the posts

• Remove paper backing, and stick (2) Silicone No Scratch Pads (O) to the bottom of each foot
• Insert Portable Foot (H) into the center cavity at the bottom of the post

Note: Inserting the portable feet may require some light force. Portable feet can be removed for storage

• Install the Post Cap (A) over the top of the post to complete the fence assembly

• Continue the fence run with any additional purchased panels
• One finishing post will be required for the end of your fence run

• Align the pre-drilled hole of the Panel Lock (N) with the pre-drilled hole in the top post hinge piece
• Drive a ½" Self-Drilling Stainless Steel Screw (M) into the pre-drilled hole

Note: Rotate the panel lock to lock and unlock the vertical movement of the panel

Soft ground: Purchase ½" diameter rebar spikes or similar stake and drive them through the holes in the foot to further secure the panel if needed

Hard surface: Purchase ½" diameter lag bolts for wood surfaces or concrete wedge anchors for a concrete surface to further secure the panels if needed

• Email: support@zippity-outdoor.com
• Phone: 704-892-5222 or 877-234-6196
• Text: 980-580-6508