Keswick Vinyl Privacy Fence

• Check the inside of the larger pieces in your box for other materials packed inside.
• When assembling, place components on a non-abrasive surface (e.g., the shipping box) to avoid scratching.
• Use an area approximately 5′ × 8′ for unobstructed assembling.
• You should not need to use excessive force when assembling components.

Returns: Please let us help resolve any issues before initiating a return. If a return is still necessary, it must be initiated with the retailer where the product was purchased.

Our US-based customer service team is available Monday–Friday, 9am–5pm EST.

• Website: https://parts.nychbrands.com
• Email: support@zippity-outdoor.com
• Phone: 704-892-5222 or 877-234-6196

For faster service, have your item number (ZP19060) and part name ready. A batch lot number (stamped on the inside/end of the box) is also helpful — it assists us in identifying and resolving any production issues.

A

Vertical Slat (20)
¼" x 1¼" x 11⅛"

B

Ground Stake (4)
¾" x 1¼" x 20"

C

Post Cap (4)

D

Left Post (2)
⅞" x 1½" x 44"

E

Right Post (2)
⅞" x 1½" x 44"

F

End Rail (4)
⅝" x ⅝" x 41⅞"

G

Middle Rail (4)
⅝" x ⅝" x 41⅞"

Middle rails have routed holes on both sides.

H

Board– Narrow (2)
⅜" x 3" x 41¾"

I

Board– Wide (6)
⅜" x 8½" x 41⅞"

J

Zippity Joiner Clip (4)

K

¾" Self-Drilling Stainless Steel Screw (24)

• Check the inside of the larger pieces in your box for other materials packed inside.

Parts Required

D x1 E x1 B x2 K x2

• Insert two Ground Stakes (B) into the bottom of the Left Post (D) and Right Post (E).
• Slide the ground stakes up into the posts until the pre-drilled holes in the stakes align with the pre-drilled holes in the posts.

• Drive (2) ¾″ Self-Drilling Stainless Steel Screws (K) into the lowest pre-drilled holes on each post to secure the stakes.

Parts Required

D x1 H x1 I x3 K x1

1

• Lay out (1) Left Post (D) and slide (1) Narrow Board (H) into the bottom of the routed grooves in the post.

2

• Insert (3) Wide Boards (I) into the slots in the post above the narrow board.

3

• Drive (1) ¾″ self-drilling stainless steel screw (K) into the second-lowest pre-drilled hole on the left post to secure the boards.

Parts Required

A x10 G x2 F x2

• Insert (10) Vertical Slats (A) into the routed holes in the Middle Rails (G)

• Place (1) End Rail (F) over the top of the picket tabs as shown
• Note: Middle rails (G) have picket holes on both sides.

• Place the second End Rail (F) over the bottom of the pickets to complete the lattice top assembly.

Parts Required

D x1 E x1 K x5

Attach Lattice Top to Left Post

• Slide the assembled lattice top into the routed holes in the Left Post (D)
• Drive (2) ¾″ self-drilling stainless steel screws (K) into the pre-drilled holes in the post to secure the lattice top

Attach Right Post

• Starting from the bottom of the Right Post (E), slide the routed holes of the post over the boards and rails
• Important! Ensure all boards and rails are fully seated into the right post

• Drive (3) ¾″ self-drilling stainless steel screws (K) into the pre-drilled holes in the right post to secure the assembly.

• Move the assembled panel to its final location and identify the positions of the posts.
• Attempt to push the panel into the ground as illustrated.

Optional For Hard Ground

Complete only if the ground is too hard to push the panel in by hand.

• Loosen the top 4″ of soil with a claw hammer or similar tool.
• Add water to further loosen the soil if necessary.
• Place a block of wood over the top of each post to protect it and gently hammer the post into the ground until fully seated.

Parts Required

J x4 K x8

• Straight-line application: Secure each Zippity Joiner Clip (J) with (2) ¾″ self-drilling stainless steel screws (K) as shown in a straight line.

• Corner application: Secure each Zippity Joiner Clip (J) with (2) ¾″ self-drilling stainless steel screws (K) as shown to make a corner.

Parts Required

C x4

• Email: support@zippity-outdoor.com
• Phone: 704-892-5222 or 877-234-6196
• Text: 980-580-6508