General Information

Important Safety Notes:

• Check the inside of the larger pieces in your box for other materials packed inside.
• When assembling components, place on a non-abrasive surface (i.e., shipping box) to avoid scratching.
• We recommend an area approximately 5' x 8' for unobstructed assembling.
• You should not need to use excessive force when assembling components.

Returns:
If you wish to return your product, please contact us first — we can often help resolve the issue right away.
If a return is still necessary, it must be initiated with the retailer where the product was purchased.

Need Help or Replacement Parts?

Although great care has been taken to ensure proper packaging and handling of this product, occasional issues can occur.

If you need replacement parts, assembly assistance, or have questions about the product, our customer service team is happy to help.

• Website: https://parts.nychbrands.com
• Email: support@zippity-outdoor.com
• Phone: 704-892-5222 or 877-234-6196

Customer service agents are available 9am–5pm EST, Monday–Friday.

For Quick Assistance:

• Have reference item number ZP19080
• Provide the specific part name
• Include the batch lot number

Detailed Dimensions & Specifications

Product Specifications:

• Overall Dimensions: 48" W x 30" L x 75½" H
• Floor weight capacity: 20 lbs
• Includes adjustable slat, mesh bags, towel hooks, and bungee connectors
• Designed for outdoor poolside organization

Power Drill and Drill Bit

Required for a smoother installation experience.

A. Post A (1)

2¾" x 2¾" x 40"

B. Post B (1)

2¾" x 2¾" x 40"

C. Post C (1)

2¾" x 2¾" x 75⅜"

D. Post D (1)

2¾" x 2¾" x 75⅜"

E. Bottom Board Long – Front (1)

44¼" x 7⅜" x ⅞"

F. Bottom Board Long – Back (1)

44¼" x 3" x ⅞"

G. Short Bottom Board (2)

26⅜" x 7⅜" x ⅞"

H. Short Slat (4)

26⅜" x 3" x ⅞"

I. Floor Board (6)

26⅞" x 4½" x ⅞"

J. Long Adjustable Slat (1)

42" x 3" x ⅞"

K. Long Slat (18)

44¼" x 3" x ⅞"

L. Post Filler (38)

1" x 1" x ⅜"

M. Post Filler (4)

3⅜" x 1" x ⅜"

N. Post Filler (2)

8½" x 1" x ⅜"

O. Post Filler (8)

11⅛" x 1" x ⅛"

P. Post Filler (2)

11½" x 1" x ⅛"

Q. Post Filler (2)

35½" x 1" x ⅜"

R. Post Hinge (4)

S. Post Cap (4)

T. Towel Hook (6)

U. Long Self-Drilling Screw (40)

2½" Long

V. Bungee Connector (2)

W. Bungee (3)

X. Mesh Bag (2)

• Slide (2) Spacers (M) to bottom of Post (C) until it meets the post cap.

• Align Posts (C) and (D) as shown.
• Assemble on box of other smooth surface to prevent scratching.

Top Down View

• Insert Bottom Board Long - Back (F) with supports facing upward.

• Temporarily place (1) Long Slat (K) to hold the frame square.

  Note: You will remove Long Slat (K) after Step 5.

• Attach Bottom Board Long - Back (F) using (4) Long Self-Drilling Screws (U).

Tip: Ensure the bottom board is pushed to the back of the post channels before driving your screws.

• Remove Long Slat (K).

• Install (34) Post Fillers (L) and (17) Long Slats (K).

• Secure with (2) Long Self-Drilling Screws (U).

• Flip panel

• Insert (2) Short Bottom Boards (G) into Posts (C) and (D).

• Secure using (4) Long Self-Drilling Screws (U).

• Temporarily insert (2) Short Slats (H).

• Slide (2) Spacers (M) to the bottom of Post (A) until they meets the post cap.

• Set Posts (A) and (B) over the boards as shown.

• Align wheel positioning per diagram for Post (B).

  Note: Make sure your wheel is in-line with the back wheel.

• Secure Posts (A) and (B) using (4) Long Self-Drilling Screws (U).

• Install Bottom Board Long - Front (E).

  Note: Ensure pre-installed floor support is at the bottom of Bottom Board Long - Front (E) when inserted into the posts.

• Secure using (4) Long Self-Drilling Screws (U).

Note: Remove Short Slats (H) after this step, before standing your poolside organizer up.

• Secure (1) Bungee Connector (V) into (1) Short Slat (H) with (3) Long Self-Drilling Screws (U).

  Note: End of bungee connector will be roughly 5 inches away from edge of short slat.

• Repeat this twice.

• Install (4) Post Fillers (O).

• Install (2) Short Slats (H) from Step 16.

  Note: Make sure you have installed the Bungee Connectors (V) from Step 16.

-Install (4) Post Fillers (O) and (2) Short Slats (H)

• Secure using (8) Long Self-Drilling Screws (U).

• Install (6) Floor Boards (I).

Floor weight capacity: 20 lbs.

• Install (2) Post Fillers (L), (2) Post Hinges (R), and (2) Post Fillers (N).

• Secure using (2) Long Self-Drilling Screws (U).

• Install (1) Long Slat (K).

• Secure Long Slat (K) with (4) Long Self-Drilling Screws (U).

• Install (2) Post Fillers (P), (2) Post Hinges (R), and (2) Post Fillers (L).

• Secure using (2) Long Self-Drilling Screws (U).

• Install Long Adjustable Slat (J).

Tip: For easier access place the long adjustable slat in the lower position.

• Install (2) Post Fillers (Q).

• Install (3) Bungees (W).

• Install (4) Post Caps (S).
• Install (6) Towel Hooks (T). Towel hooks can be arranged to fit your needs.

• Email: support@zippity-outdoor.com
• Phone: 704-892-5222 or 877-234-6196
• Text: 980-580-6508